Jump to the page content

If this page has its own menu, you can click here to jump to the page menu

Jump to main menu

 
 
 
 
Jump to top of page
Blogs
  • Variations in Spur Design | Ranch Supply Review
    As you're probably aware, spurs are worn on the heels of your riding boots and used to direct the animal. Although we're used to seeing spurs with sharp rowels (the spiked area), there are actually an assortment of spur designs: ~Round End: The rounded metal ball instead ... ~Rowelled: With a spinning, toothed wheel, these spurs are most commonly used for western riding. ~Knob End: The end of the spur is squared off but still has blunt edges to get the horse's attention. ...
    Equestrian-Time
    15 Hours 29 Minutes ago
    http://www.ranchsupplyreview.com/
  • Micro Sumo Robot | Let's Make Robots!
    Bot dims are 49mm x 49mm x 55mm tall. Lower plate supports the motor/gearbox. The middle plate is used to mount the Edge Sensors and the Upper Plate supports the Battery holder and Sharp IR Sensor plus risers for the PCB. ... Tires are natural closed cell foam rubber 0.25" (6.4mm) wide. Gears: These items are also from slotcars. 64 pitch 38 tooth spur and a 12 tooth pinion. 3.16:1 gear ratio. Axles are 0.094 dia. and each axle rides in (2) ball bearings. ...
    -Gary
    Thursday, July 29, 2010 7:14 PM
    http://letsmakerobots.com/
  • Rowel NBA Rowell Logo Spur Auctions | TechBanyan
    CoolSpurs2(1) Rowel NBA Rowell Logo A lot of you are asking what is a Rowel. (Sometimes also confused for Rowell or Rowal etc.) The correct spelling is Rowel and it is a sharp-toothed wheel inserted into the end of the shank of a spur. ...
    Troy
    Friday, September 19, 2008 9:29 PM
    http://www.techbanyan.com/
  • Can someone cut a bevel gear tooth for me? - Practical Machinist ...
    However, I understand bevel gears are cut differently than a spur gear, and besides which, I have no indexer or fixture to hold this at the proper bevel angle. I'd figured that I'd make some rough fixture (it's just the one tooth) just eyeball the cut, .... If you were re-cutting the whole gear (or two, as I was) this would probably be a good idea, but for one tooth, you are going to spend more time setting up than you would with a good sharp file carving a new tooth. ...
    DocsMachine
    Thursday, October 29, 2009 3:00 AM
    http://www.practicalmachinist.com/vb/
  • Gear Set
    The blades, hand-finished in Switzerland, are constructed of high-carbon, no-stain steel, with a full tang for superior strength and balance. The knives retain their sharp edges and are readily resharpened when necessary. ...
    Corey
    Thursday, January 07, 2010 11:31 PM
    http://www.torbettautosupply.com/
  • Fitting a Slot.it HRS2 Chassis under a Carrera Bentley EXP Speed 8 ...
    There is no room for a spur gear in the wheel well or even beside it unless you tighten the motor pod screws completely to eliminate all play, but that defeats the purpose. I also experimented with the .... You might try cutting away the sharp edge of the crown gear on the non-tooth side to provide a bit more clearance (that was suggested to me for dropping a Slot.it gear into a Scalextric MG Lola that needed more clearance in that same place). But modifying the body to ...
    PT Fan
    Wednesday, April 22, 2009 3:37 PM
    http://www.slotcarillustrated.com/portal/forums/
  • Sportwerks Turmoil RTR
    It features a full six-gear setup, which the only significant difference being the fact that the open end is capped by a spur gear instead of a ring gear. The 46-tooth spur gear is hardened steel, making it tough enough to handle the abuse the .26 ... The Sportwerks 26 V2 is finished in black oxide, giving it a very nice sharp looking finished look. On the back you'll find a rotary start backplate which gives you an easy way to get the Turmoil up and running quickly. ...
    unknown
    Monday, October 09, 2006 3:00 AM
    http://www.rcuniverse.com/mag/
  • Tutorial Membongkar Mechbox Ver.2
    It contains large and clearly defined teeth that directly engages the piston as well as a small rack on the underside which also engages the spur gear. To get a better picture, scroll down in the images below. The sector gear also has a ...
    odedtea
    Monday, July 28, 2008 2:50 AM
    http://odedtea.wordpress.com/
News
  • No results found.
Images
Video
Websites
Local Business

Jump To Top of Page


Country/Language: United States
Share |
Tip: Press F11 for Full Screen